Laser Tracker 1.5 Sphere Mounts & Accessory (2024)

1.5SM

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a hole and 1.000 above or 25mm above.1.5 ...

1.5 SMN

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole and 1.000 above or optional 2...

1.5 SMN/MB

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole and 1.000 above or 25mm above...

1.5 SMN-SS (1.250 Body)

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole and 1.000 above or 25mm above...

1.5 SM-SS (1.00 Body)

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole and 1.000 above or 25mm above...

1.5 SMSI

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole and 1.000 or 25 mm offset abo...

1.5 NMSM

Designed to locatea Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole when a magnet is not d...

1.5 SM/DS

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of standard slotted type bushings.1.5 S...

1.5 SMT

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory on centerline of a threaded hole and 1.000 above or&n...

1.5 SSM

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

1.5 SSM/MB

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

1.5 SSM/M6

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

1.5 SSM/MB-CP

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge ...

1.5 SSM/MB-CPL

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for a critical height and centerline. The edge may be...

1.5 GLSM

Used to represent the control side of a groove that is in an automotive grid plate at 1.000 or 25mm above and will clear 3mm by 3mm groove or slot.1.5 GLSM FEATURES: 1144 STEEL, BLACK OXIDE FINISH &nd...

1.5 ESM

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces. The 1.5ES...

1.5 ESM-2

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces.1.5 ESM - ...

1.5 ESM-OC

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating outside corners.1.5 ESM -...

1.5 ESM-2-OC

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating outside corners.1.5 ESM -...

1.5 ESM-2-1/4

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpse of locating inside corners or radius.N...

1.5 ISMP

Designed to adapt a 1.5 Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory to an Invar Scale Bar.1.5

1.5 TSM

Adapts to a Theodolite Adaptor to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory in place for a consistant ...

1.5 LT-RSM

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory as a permanent reference point.1.5 LT - RSM FEATURES:...

1.5 SM-DN-3PA

Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives.1.5 SM - DN - 3PA FEATURES: ALUMINUM BLACK, HARD ANODIZED COATING• Low cost• Lightwe...

1.5 SMN-DN-3PA

Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives, and allows for rotation below horizontal.1.5 SMN - DN - 3PA FEATURES: ALUMINUM BLACK, HARD AN...

1.5 SM-DN-3PS

Used for establishing non-critical temporary or permanent monuments using adhesives or by tack welding.NOTE: We suggest removing the magnet before welding.1.5 SM - DN - 3PS FEATURES: 1144 STEEL, BLACK...

1.5 SMN-DN-3PS

Used for establishing non-critical temporary or permanent monuments using adhesives or by tack welding, and allows for rotation below horizontal.NOTE: We suggest removing the magnet before welding.1.5...

1.5 SM-HC

Designed for mounting to a surface to securely hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory. The 1.5SM-H...

1.5 SM-HC/MB

Designed for mounting to a surface to securely hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory. The 1.5SM-HC/MB is use...

1.5 SM-HC/CP

Designed for adhering to a steel surface to securely hold a Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target ...

1.5 SM-TM

Sometimes called a “hockey puck,” the 1.5 SM-TM provides a temporary magnetic SMR adaptor in almost any location on any surface by using hot glue to attach the adaptor temporarily.1.5 SM -...

1.5 TPSN

Allows the SMR to be tracked into a position. A light tap with a hammer will produce a small accuratedly located center punch mark under the SMR location without removing the SMR. Item intended for la...

1.5 CPSN

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating center punch marks withou...

1.5 FSM

Mounted in concrete flooring/foundations, etc., to allow for a permanent 1.5 spherical target reference.1.5 FSM FEATURES: STAINLESS STEEL (standard)SM is a Registered Trademark of Hubbs Machine & ...

1.5 SMR/MC

Holds a 1.5 inch SMR magnetically to a flat, ferrous surface. It can also hold a Theodolite or Photogrammetry Sphere in some orientations.1.5 SMR / MC FEATURES: ALUMINUM BLACK, ANODIZED COATING...

1.5 SM-PA

Designed to adapt a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory to a customer-supplied pole extension (painting...

LLST

Designed to achieve the centerline of the Leveling Lug.LLST FEATURES: STAINLESS STEEL WITH 1144 STEEL, BLACK OXIDE INSERT - Heat-treated and hardened to R/C 53 - 55 (standard)LLST APPLICAT...

LT-LOSA

Adapts a 1.5 Spherically Mounted Retro-Reflector to replace the standard optic 3 1/2” diameter line of sight spherical target.LT - LOSA FEATURES: 1144 STEEL, BLACK OXIDE FINISH - Heat-trea...

1.5-.5 SMR AD

Designed to adapt a 1.5 Sphere Mount Nest to .5000 Spherically Mounted Retro-Reflector.1.5 - .5 SMR AD FEATURES: STAINLESS STEEL Heat-treated and hardened to R/C 53 - 55 (standard)...

1.5-.875 SMR AD

Designed to adapt a 1.5 Sphere Mount Nest to .8750 Spherically Mounted Retro-Reflector.1.5 - .875 SMR AD FEATURES: STAINLESS STEEL Heat-treated and hardened to R/C 53 - 55 (standard)...

1.5 RRS (Ball)

Adapts a Retro-Probe tip to centerline of 1.5000 Sphere to within .00025.NOTE: Nest for probe tip diameter from 1mm to .25001.5 RRS (BALL) FEATURES: STAINLESS STEEL BALL with 17-4 stainless steel inse...

1.5 HPA

Designed to adapt to a 1.5 Sphere Mount Nest in an inaccessible location using .2500 shank applicable accessories.1.5 HPA FEATURES: STAINLESS STEEL WITH 1144 STEEL, BLACK OXIDE INSERT - Heat-tre...

T1.5S

T1.5S provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to computer-aided Theodolite systems.T1.5S FEATURES: STAINLESS ...

SMR Lanyard Set (full)

Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left,drawings show included items in full or partial set.SMR...

SMR Lanyard Set (partial)

Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.SM...

Leica Lanyard Set (full)

Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.LE...

Leica Lanyard Set (partial)

Designed to tether a 1.5 Spherically Mounted Retro-Reflector to the user or Sphere Mount, preventing loss or damage.NOTE: Full set shown at left, drawings show included items in full or partial set.LE...

1.5 SMV

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of a hole. Use the variable design to c...

1.5 SMV/DS

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessoryon centerline of standard slotted type bushings.1.5 S...

1.5 SMP

PSS

The Precision Scan Sphere provides the same centerline value as a 1.500” Spherically Mounted Retro-Reflector. This allows interchangeability of targeting from Laser Tracker systems to Laser Scan...

1.5 SMPT

R1.5 S

Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Photogrammetry or Videogrammetry systems.1.5S FEATURES: HARDENED S...

W1.5 S

Provides same centerline value as a Spherically Mounted Retro-Reflector. This allows interchangeability from Laser Tracker systems to Contrast Photogrammetry or Videogrammetry systems.1.5S FEATURES:&n...

1.5 SMP-DN-2

1.5 ESM/MB-2

Designed to hold a Spherically Mounted Retro-Reflector, Theodolite Sphere, Photogrammetry Sphere, or other Spherical Type Target or Accessory for the purpose of locating edges/surfaces.1.5 ESM - ...

TOTAL1.5S

Provides same centerline value as a Spherically Mounted RetroReflector. This allows interchangeability from Laser Tracker systems to Total Station systems.TOTAL 1.5S FEATURES:...

1.5SM-BNL-3PA

Used for establishing non-critical temporary or permanent monuments using hot-glue or permanent adhesives or it can be bolted on.

Super Precision Scan Sphere (SPSS)

The Super Precision Scan Sphere (SPSS) provides the same centerline value as a 1.500” Spherically Mounted Retro-Reflector. The SPSS fits over any 1.5 spherical item to hold the same center within .002”, including a SMR. Diameter held to within .002”. A 1.500 sphere is included with every SPSS. This allows interchangeability of targeting...