Microturbines | WBDG - Whole Building Design Guide (2024)

Introduction

Within This Page

  • Introduction
  • Description
  • Application
  • Relevant Codes and Standards
  • Additional Resources

Microturbines are a relatively new distributed generation technology being used for stationary energy generation applications. They are a type of combustion turbine that produces both heat and electricity on a relatively small scale.

Microturbines offer several potential advantages compared to other technologies for small-scale power generation, including: a small number of moving parts, compact size, lightweight, greater efficiency, lower emissions, lower electricity costs, and opportunities to utilize waste fuels. Waste heat recovery can also be used with these systems to achieve efficiencies greater than 80%.

Because of their small size, relatively low capital costs, expected low operations and maintenance costs, and automatic electronic control, microturbines are expected to capture a significant share of the distributed generation market. In addition, microturbines offer an efficient and clean solution to direct mechanical drive markets such as compression and air-conditioning.

Microturbines | WBDG - Whole Building Design Guide (1)

Microturbines work like jet engines but produce electricity instead of thrust.
Photo Credit: Capstone Turbine Corp.

Description

A. What is a Microturbine?

Microturbine Overview
Commercially AvailableYes (Limited)
Size Range25-500 kW
FuelNatural gas, hydrogen, propane, diesel
Efficiency20-30% (Recuperated)
EnvironmentalLow (<9–50 ppm) NOx
Other FeaturesCogeneration (50–80°C water)
Commercial StatusSmall volume production, commercial prototypes now.

(Courtesy of California Distributed Energy Resources Guide on Microturbines)

Microturbines are small combustion turbines approximately the size of a refrigerator with outputs of 25 kW to 500 kW. They evolved from automotive and truck turbochargers, auxiliary power units (APUs) for airplanes, and small jet engines. Most microturbines are comprised of a compressor, combustor, turbine, alternator, recuperator (a device that captures waste heat to improve the efficiency of the compressor stage), and generator. The figure below illustrates how a microturbine works.

Microturbines | WBDG - Whole Building Design Guide (2)

How a microturbine works.
Courtesy of slimfilms.com

B. Types of Microturbines

Microturbines are classified by the physical arrangement of the component parts: single shaft or two-shaft, simple cycle, or recuperated, inter-cooled, and reheat. The machines generally rotate over 40,000 revolutions per minute. The bearing selection—oil or air—is dependent on usage. A single shaft microturbine with high rotating speeds of 90,000 to 120,000 revolutions per minute is the more common design, as it is simpler and less expensive to build. Conversely, the split shaft is necessary for machine drive applications, which does not require an inverter to change the frequency of the AC power.

Microturbine generators can also be divided into two general classes:

  • Unrecuperated (or simple cycle) microturbines—In a simple cycle, or unrecuperated, turbine, compressed air is mixed with fuel and burned under constant pressure conditions. The resulting hot gas is allowed to expand through a turbine to perform work. Simple cycle microturbines have lower efficiencies at around 15%, but also lower capital costs, higher reliability, and more heat available for cogeneration applications than recuperated units.

  • Recuperated microturbines—Recuperated units use a sheet-metal heat exchanger that recovers some of the heat from an exhaust stream and transfers it to the incoming air stream, boosting the temperature of the air stream supplied to the combustor. Further exhaust heat recovery can be used in a cogeneration configuration. The figures below illustrate a recuperated microturbine system. The fuel-energy-to-electrical-conversion efficiencies are in the range of 20 to 30%. In addition, recuperated units can produce 30 to 40% fuel savings from preheating.

Microturbines | WBDG - Whole Building Design Guide (3)

Microturbines | WBDG - Whole Building Design Guide (4)

Recuperated microturbine
Photo Credit: Capstone

View enlarged diagram
Courtesy of EPRI

Cogeneration is an option in many cases as a microturbine is located at the point-of-power utilization. The combined thermal electrical efficiency of microturbines in such cogeneration applications can reach as high as 85% depending on the heat process requirements.

Microturbine Efficiency
ConfigurationEfficiency
Unrecuperated15%
Recuperated20–30%
With Heat RecoveryUp to 85%

(Courtesy of California Distributed Energy Resources Guide on Microturbines)

Advanced materials, such as ceramics and thermal barrier coatings, are some of the key enabling technologies to further improve microturbines. Efficiency gains can be achieved with materials like ceramics, which allow a significant increase in engine operating temperature.

C. Characteristics of Microturbines

Some of the primary applications for microturbines include:

  • Distributed generation—stand-alone, on-site applications remote from power grids
  • Quality power and reliability—reduced frequency variations, voltage transients, surges, dips, or other disruptions
  • Stand-by power—used in the event of an outage, as a back-up to the electric grid
  • Peak shaving—the use of microturbines during times when electric use and demand charges are high
  • Boost power—boost localized generation capacity and on more remote grids
  • Low-cost energy—the use of microturbines as base load or primary power that is less expensive to produce locally than it is to purchase from the electric utility
  • Combined heat and power (cogeneration)—increases the efficiency of on-site power generation by using the waste heat for existing thermal process.

Microturbines offer many potential advantages for distributed power generation. Selected strengths and weaknesses of microturbine technology are listed in the following table from the California Distributed Energy Resources Guide on Microturbines.

Microturbines
StrengthsWeaknesses
Small number of moving partsLow fuel to electricity efficiencies
Compact sizeLoss of power output and efficiency with higher ambient temperatures and elevation
Lightweight
Good efficiencies in cogeneration
Low emissions
Can utilize waste fuels
Long maintenance intervals
No vibrations
Less noise than reciprocating engines
Strengthens energy security

Accessible: N/A

Aesthetics:

  • Improves sightlines and views with off-the-grid systems, which eliminate the need for overhead power lines

Cost-Effective: (See Section F: Economics of Microturbines)

  • Enables cost savings by reducing the peak demand at a facility, therefore lowering demand charges

Functional:

  • Provides better power reliability and quality, especially for those in areas where brownouts, surges, etc. are common or utility power is less dependable
  • Provides power to remote applications where traditional transmission and distribution lines are not an option such as construction sites and offshore facilities
  • Can be an alternative to diesel generators for on-site power for mission critical functions (e.g., communications centers)
  • Possesses combined heat and power capabilities
  • Reduces upstream overload of transmission lines
  • Optimizes utilization of existing grid assets—including potential to free up transmission assets for increased wheeling capacity
  • Improves grid reliability
  • Facilitates faster permitting than transmission line upgrades
  • Can be located on sites with space limitations for the production of power

Productive:

  • Provides high-quality power for sensitive applications
  • Responds faster to new power demands—as capacity additions can be made more quickly
  • Facilitates less capital tied up in unproductive assets—as the modular nature of microturbines means capacity additions and reductions can be made in small increments, closely matched with demand, instead of constructing central power plants sized to meet estimated future (rather than current) demand
  • Stand-by power decreases downtime, enabling employees to resume working
  • Produces less noise than reciprocating engines

Secure/Safe:

  • Strengthens energy security
  • Stand-by power provides quick recovery after an event

Sustainable:

  • Produces the lowest emission of any noncatalyzed fossil fuel combustion system
  • Has a small footprint, minimizing site disturbance
  • Reduces or defers infrastructure (line and substation) upgrades
  • For recuperated microturbine, possesses higher energy conversion efficiencies than central generation
  • Enables more effective energy and load management

D. Economics of Microturbines

Microturbine capital costs range from $700–$1,100/kW. These costs include all hardware, associated manuals, software, and initial training. Adding heat recovery increases the cost by $75–$350/kW. Installation costs vary significantly by location but generally add 30-50% to the total installed cost.

Microturbine manufacturers are targeting a future cost below $650/kW. This appears to be feasible if the market expands and sales volumes increase.

With fewer moving parts, microturbine vendors hope the units can provide higher reliability than conventional reciprocating generating technologies. Manufacturers expect that initial units will require more unexpected visits, but as the products mature, a once-a-year maintenance schedule should suffice. Most manufacturers are targeting maintenance intervals of 5,000-8,000 hours.

Maintenance costs for microturbine units are still based on forecasts with minimal real-life situations. Estimates range from $0.005–$0.016 per kWh, which would be comparable to that for small reciprocating engine systems.

Microturbine Cost
Capital Cost$700–$1,100/kW
O&M Cost$0.005-0.016/kW
Maintenance Interval5,000-8,000 hrs

(Courtesy of California Distributed Energy Resources Guide on Microturbines)

Application

Microturbines can be used for stand-by power, power quality and reliability, peak shaving, and cogeneration applications. In addition, because microturbines are being developed to utilize a variety of fuels, they are being used for resource recovery and landfill gas applications. Microturbines are well suited for small commercial building establishments such as: restaurants, hotels/motels, small offices, retail stores, and many others.

The variety of energy consumers that are already using microturbines is large and growing fast. For example:

  • Landfill gas-fired microturbines installed at the Jamacha Landfill in Spring Valley, California supply power on-site and back to the grid. More

  • A McDonald's restaurant in Chicago, Illinois, gets most of its electricity from a natural-gas-powered microturbine, cutting $1,500 off its total monthly power bill.

A Parallon 75 microturbine generator power system at The Energy Efficient McDonald's (TEEM) in Bensenville, Illinois, is able to power the entire store, including lighting, cooking equipment, and HVAC.
Photo Credit: Energy User News

Microturbines | WBDG - Whole Building Design Guide (5)

  • A textile mill in Lawrence, Massachusetts, ensures continuous operation by getting its power from microturbines.

  • The Chesapeake Building on the University of Maryland campus, College Park, Maryland has a cooling, heating, and power (CHP) system consisting of microturbines, chiller, and stack that uses waste heat to cool and heat the building, significantly increasing system efficiency.

Microturbines | WBDG - Whole Building Design Guide (6)

Chesapeake Building CHP system, University of Maryland—College Park, MD

The development of microturbine technology for transportation applications is also in progress. Automotive companies are interested in microturbines as a lightweight and efficient fossil-fuel-based energy source for hybrid electric vehicles, especially buses.

Other ongoing developments to improve microturbine design, lower costs, and increase performance in order to produce a competitive distributed generation product include heat recovery/cogeneration, fuel flexibility, and hybrid systems (e.g., fuel cell/microturbine, flywheel/microturbine).

Relevant Codes and Standards

Additional Resources

State and Federal Agencies

Associations and Organizations

  • California Communities for Advanced Distributed Energy Resources (CADER)—Serves as an information clearinghouse on efficient technologies and infrastructure systems that improve the quality, reliability and security of community energy supplies, while reducing energy costs and environmental impacts associated with power generation.
  • CHP Association—An association that brings together diverse market interests to promote the growth of clean, efficient CHP in the United States. Its mission is to create a regulatory, institutional, and market environment that fosters the use of clean, efficient CHP as a major source of electric power and thermal energy in the U.S. (Formerly U.S. Clean Heat and Power Association (USCHPA))
  • World Alliance for Decentralized Energy (WADE)—Launched by a group of major companies and national industry associations to accelerate the development of high efficiency cogeneration and decentralized energy (DE) systems which will deliver substantial economic and environmental benefits worldwide.

Manufacturers

There are more than twenty companies worldwide that are involved in the development and commercialization of microturbines for distributed generation applications. Below are links for five of the leading microturbine manufacturers.

  • Bowman Power Systems—A U.K. company that develops 80-kW microturbine power generation systems for DER and mobile power applications.
  • Calnetix Technologies—A premier manufacturer of microturbines for use in distributed generation, combined heat and power (CHP), biogas and offshore applications.
  • Capstone Turbine Corporation—Based in Chatsworth, CA, Capstone is a leader in the commercialization of low-emission, high-reliability microturbine power generators. The company offers 30-kW and 60-kW systems for DER applications.
  • Ansaldo Turbec— In late 2012 Ansaldo Energia acquired Turbec. The company offers a 100-kW microturbine power generator for commercial DER applications.
Microturbines | WBDG - Whole Building Design Guide (2024)

FAQs

What is the whole building design process? ›

Whole-building design refers to a design and construction technique that incorporates an "integrated design approach" and an "integrated team process."1 Basically, all of the elements of a building's design need to be considered, and all team members/design stakeholders need to be involved in new ways earlier in the ...

What is the UFC design standard? ›

Description. The Unified Facilities Criteria (UFC) system is prescribed by MIL-STD 3007 and provides planning, design, construction, sustainment, restoration, and modernization criteria, and applies to the Military Departments, the Defense Agencies, and the DoD Field Activities.

What does WBDG stand for? ›

Whole Building Design and the WBDG® | WBDG - Whole Building Design Guide.

What service are the UFCs applicable to? ›

The Unified Facilities Criteria (UFC) system (prescribed by MIL-STD 3007) provides planning, design, construction, sustainment, restoration, and modernization criteria; applicable to the Military Departments, the Defense Agencies, and the DoD Field Activities; in accordance with DoD Directive 4270.5, Military ...

What are the 7 steps in the building process? ›

What Are The Stages Of A Construction Project?
  • Step 1: Design. During this phase, the client places a project for bidding. ...
  • Step 2: Pre-Construction. ...
  • Step 3: Procurement. ...
  • Step 4: Construction. ...
  • Step 5: Commissioning. ...
  • Step 6: Owner Occupancy. ...
  • Step 7: Project Closeout.

What are the 7 phases of architectural design? ›

The architectural design process is made up of seven phases: pre-design, schematic design, design development, construction documents, building permits, bidding and negotiation and construction administration.

What is C class MMA? ›

C-Class (Amateur), in addition to A-Class & B-Class exclusions: a) Any strikes to the head of a grounded competitor, b) Kicking the body of a grounded competitor, c) Up-kicks to the body of a standing competitor from a grounded competitor, d) Knee strikes to the head.

How many styles are in MMA? ›

3 Main MMA Fighting Styles: Striking, Jiu Jitsu, And Wrestling - The Arena.

What does CX mean in construction? ›

Building commissioning (Cx) is a professional practice that facilitates the planning, design, construction, installation and testing verification, documentation, and operation of facilities and systems to conform to the Owner's Project Requirements (OPR).

What is whole building commissioning? ›

the Building. Commissioning Process Overview. Commissioning is a process – a systematic process of ensuring that a building performs in accordance with the design intent, contract documents, and the owner's operational needs. Commissioning is fundamental to the success of the whole-building design process.

What is total building commissioning? ›

Total Building Commissioning ensures that the performance of the facility and all its systems meet the near and long-term functional and operational needs of the owner and occupants.

What are the 5 phases of building? ›

The five phases of the construction project lifecycle are:
  • Project Initiation and Conception. Like with all things, the first step to the construction life cycle is merely to begin. ...
  • Project Planning and Definition. ...
  • Project Execution and Launch. ...
  • Project Performance. ...
  • Project Close.

What are the 3 stages necessary to build a building? ›

  • Pre-Construction Phase. The pre-construction phase includes creating a strategic plan for the project, creating a design, securing permits or entitlements, and gathering the labor and resources required for construction. ...
  • Construction Phase. ...
  • Post- Construction Phase.

What are the 5 phases of the design build process? ›

The design-build process can be broken down into five main steps: team selection, project planning, design, GMP/bidding, and construction. For the most part, these steps will happen sequentially, but not necessarily independent of one another. The project planning, design, and bidding phases may overlap.

What are the 5 rules of architecture? ›

In the course of his work as an architect, Le Corbusier developed a series of architectural principles, which he used as the basis of his designs. The design principles include the following five points by Le Corbusier: Pilotis (pillars), roof garden, open floor plan, long windows and open facades.

What are the 4 rules of architecture? ›

Legibility, flexibility, durability, affordability. If a building is successful in these terms, it can be considered 'sustainable' in a wider sense (or maybe just good architecture).

What are the 5 orders of architecture parts? ›

There are five orders of columns in classical architecture: Tuscan, Doric, Ionic, Corinthian, and Composite. They range from simple to complex in this order.

What can you not do in MMA? ›

No directed throat strikes are allowed. A directed attack would include a fighter pulling his opponents head in a way to open the neck area for a striking attack. A fighter may not gouge their fingers or thumb into their opponent's neck or trachea in an attempt to submit their opponent.

What is under MMA? ›

mixed martial arts (MMA), hybrid combat sport incorporating techniques from boxing, wrestling, judo, jujitsu, karate, Muay Thai (Thai boxing), and other disciplines.

What is grading in MMA? ›

What is “grading”? A certified coach shall “grade” his student by evaluating his/her ability to demonstrate and explain particular techniques. This is commonly conducted as a “grading exam, or display” in front of peers and/or parents.

What does heart mean in UFC 3? ›

It's basically how much damage you can take before you get knocked out. "You have heart kid"

What class is Conor McGregor in UFC 3? ›

McGregor is a Featherweight fighter in the UFC. He typically fights at 145 pounds.

What style of fighting does John Wick use? ›

None other than Jeet Kune Do, which taught him to assess his actors' physical attributes to determine how they would move and fight. Like Bruce Lee and Donnie Yen before him, John Wick's fighting style “absorbs what is useful and rejects what is useless.”

Can a female martial artist beat a man? ›

However, with all of these advantages listed out, a woman can beat a man in a mixed martial arts fight because fighting is more than just about physical ability and technique even though they play a greater role in the process of winning.

Is there 10 7 in MMA? ›

A 10 – 7 Round in MMA is when a fighter completely overwhelms their opponent in Effective Striking and/or Grappling and stoppage is warranted.” A 10 – 7 round in MMA is a score that judges will rarely give.

What are the 5 stages of design construction? ›

What Are the 5 Phases of a Design Project? The 5 phases of a design project are Schematic Design, Design Development, Construction Documents, Bidding, and Construction Administration, according to the American Institute of Architects (AIA).

What are the 5 stages of the architectural design process? ›

The American Institute of Architects (AIA) defines Five Phases of Architecture that are commonly referred to throughout the industry: Schematic Design, Design Development, Contract Documents, Bidding, Contract Administration.

What are the 6 parts of a complete building plan? ›

A building plan consists of elements such as elevations, electrical detailing, plumbing, site plan, floor plans, structural plans, cross-sections, and landscape drawings.

What are the 6 stages of the design cycle? ›

The design-thinking framework follows an overall flow of 1) understand, 2) explore, and 3) materialize. Within these larger buckets fall the 6 phases: empathize, define, ideate, prototype, test, and implement.

What are the 6 phases of design process workflow? ›

The design process consists of 6 iterative phases: focus, understand, define, conceive, build and test.

Top Articles
Latest Posts
Article information

Author: Francesca Jacobs Ret

Last Updated:

Views: 6582

Rating: 4.8 / 5 (48 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Francesca Jacobs Ret

Birthday: 1996-12-09

Address: Apt. 141 1406 Mitch Summit, New Teganshire, UT 82655-0699

Phone: +2296092334654

Job: Technology Architect

Hobby: Snowboarding, Scouting, Foreign language learning, Dowsing, Baton twirling, Sculpting, Cabaret

Introduction: My name is Francesca Jacobs Ret, I am a innocent, super, beautiful, charming, lucky, gentle, clever person who loves writing and wants to share my knowledge and understanding with you.