FAQs
Hold the reset lever in the start position until the pressure builds up and the gauge reads over 40 PSI; then let it return to the AUTO position. The pump should now run on its own and continue until the pressure reaches the cut out setting, (usually between 50 - 60 PSI), and then shut off.
Why is my submersible well pump not starting? ›
Your well pump may have stopped working due to a lack of power. Sometimes resetting a breaker or replacing a fuse affected by a power surge or brownout can fix this. If the well pump circuit breaker has tripped, the well pump itself may be failing.
Why is my submersible motor not starting? ›
Replace blown fuses and reset the breaker if it has been tripped. With the submersible pump pressure switch in a closed position, check the voltage across the switch. If the voltage drop is at the same level as the line voltage, the switch is obviously not making contact.
Do you have to prime a deep well submersible pump? ›
Submersible well pumps operate completely underwater, where the pumping unit is placed within the well casing and is connected to a power source at the top of the well. This type of well pump works best for deep wells, and does not need to be primed because it works underwater.
Why is my well pump not kicking on? ›
1) Check the Power
Check the circuit breaker connected to the well and see if there is a short in the system. If your well pump stopped working after a thunderstorm, check to see if the well was struck by lightning. If there is a short or surge in the power to your well, the circuit might have blown.
Why is my pump not kicking on? ›
Pump Won't Start
There are several reasons why a booster pump doesn't start including a lack of power, water in the break tank, tripping, sensor failure, problems with the control panel and motor failure. Firstly if there is a power cut then the pumps won't run and there will be no water delivered.
How do I know if my submersible well pump is bad? ›
Some of the most common indicators of a faulty well pump and pressure tank include:
- Fluctuations in Water Pressure. ...
- Noisy Pressure Tank or Clicking Sounds. ...
- Spitting Faucets. ...
- Scalding Shower Water. ...
- High Electric Bills.
How do I know if my well pump pressure switch is bad? ›
Signs of a bad well pressure switch
- The pump does not turn off when the tank's pressure exceeds the preset cut-off pressure.
- The pump does not turn on when the tank's pressure drops below the preset cut-on pressure.
- The pump short cycles.
- The pump is running, but the water pressure in your home is low.
How do I get the pressure back in my well pump? ›
Easy Fixes for Low Well Water Pressure
- Clean Clogged Faucets & Fixtures. Over time, faucets and fixtures get clogged with sediment and mineral deposit buildup. ...
- Adjust Your Pressure Switch. ...
- Clear Clogged Water Lines. ...
- Install a Water Softener. ...
- Install a Water Pressure Regulator.
What is the life expectancy of a submersible pump? ›
The average life expectancy is 10 to 15 years for a residential 3-wire and 8 to 13 years for a residential 2-wire well pump. Life expectancy of the pump depends on many different factors, some of which are the quality of the pump, how often the pump has to run, and the electrical supply to the pump.
Dirt, hard water minerals, small stones, or other debris can also clog the pipes leading to your pump and reduce water flow or cause the pump to stop working completely.
What makes a well pump lose prime? ›
Leaks on the pump's intake line as well as around the shaft seal of the pump housing itself can cause your pump to lose its prime.
Can a well pump lose its prime? ›
If your pump is abnormally cycling or isn't drawing water at the pressure or volume you need, the first step is to check and see if the pump is fully primed (filled to the top with water). Although it's not likely, it's possible that non-submersible well pumps can lose their prime as a result of other issues.
How can you tell if a submersible pump is bad? ›
Faulty Submersible Pump Signs
- Broken Seal: Often, lack of pressure suggests that the pump needs refilling with water. ...
- Low Pressure: ...
- Air in the Pipes: ...
- Leakage: ...
- Continuous Running Pump: ...
- Poor Water Pressure: ...
- Strange Noise: ...
- Water Contamination:
Why is my submersible pump humming but not pumping? ›
Low humming noises from a sump pump are often completely normal. However, if the pump begins humming louder than usual and/or is not pumping water, it's time to investigate. First, check the vent hole for a clog and clean it out if needed. If this doesn't help, you may have a stuck check valve.
How do you get a submersible pump to work? ›
First, ensure the pump's power is turned off for safety. Next, lower the pump into the well, ensuring the pipe and electrical cable are properly connected. Double-check that the well has enough water to cover the pump entirely. Lastly, switch the power back on and monitor the system to confirm it's working as expected.